- #Hp smart array p410i controller how to
- #Hp smart array p410i controller install
- #Hp smart array p410i controller serial
- #Hp smart array p410i controller update
- #Hp smart array p410i controller windows
The card works but no boot option to config via BIOS. Twaeking boot rom on the PCI slots did not help. I upgraded from a P400 which did not have these problems. I have a P410 in a SuperMicro X8SAX with similiar issues. Once enable, you can use putty (as ssh client) to connect to you esxi box. You can enable cmdline access directly from esxi console or via vsphere client. For more information, consult vendor documentation and support. Specify the IP address or domain name of the ESX host.ĭirections may vary depending on what SSH client you are using. Verify that the daemon selected in step 3 shows as running in the Services Properties window In ESXi 4.1, select Local Tech Support or Remote Tech Support (SSH) and click Options.Ĭhoose the desired startup policy and click Start, then click OK. In ESXi 5.x, select SSH or ESXi Shell and click Options. Select the host and click the Configuration tab. To enable local or remote TSM from the vSphere Client: Press Esc three times to return to the main DCUI screen. Input the desired timeout value in minutes and press Enter. In ESXi 4.1, select Modify Tech Support timeout and press Enter.
![hp smart array p410i controller hp smart array p410i controller](http://www.garlandcomputers.com/wp-content/uploads/imported/HP-Smart-Array-P410-RAID-Controller-Card-462919-001-013233-001-256MB-371250596341.jpg)
In ESXi 5.x, select Modify ESXi Shell timeout and press Enter. Optionally, if you want to configure the timeout for TSM: The right-hand panel mode should now indicate the "Remote TSM (SSH) is Enabled". In ESXi 4.1, select Remote Tech Support (SSH) and press Enter. In ESXi 5.x, select Enable SSH and press Enter.The right-hand panel mode should now indicate the "SSH is Enabled". To enable remote TSM allowing users to log in via SSH on the virtual console of the ESXi host. The right-hand panel mode should now indicate the Local TSM is Enabled. In ESXi 4.1, select Local Tech Support and press Enter. The right-hand panel mode should now indicate ESXi Shell is Enabled. In ESXi 5.x, select Enable ESXi Shell and press Enter. To enable local TSM allowing users to log into the virtual console of the ESXi host. This opens the Troubleshooting Mode Options wizard. Scroll to Troubleshooting Options and press Enter. To enable local or remote TSM from the Direct Console User Interface (DCUI):Īt the DCUI of the ESXi host, press F2 and provide credentials when prompted. I've connected one HD to my SAS Expander, which is connected to the HP p410 with 2x SFF-8087 cables.
#Hp smart array p410i controller install
Then you should install the Updates (what a hassle ) and get the software & drivers from HPs website.
#Hp smart array p410i controller windows
I went for a test with Windows Server 2008 R2 (Trial). I wanted to go the Debian way, but the cciss drivers are only available for 32bit (does not make much sense on a 16GB RAM machine) OR for RHEL (CentOS) & SUSE Enterprise Server. It is NOT POSSIBLE to boot off the HP p410 here! Install the desired OS onto your system HD which HAS TO BE connected to onboard or another controller (in my case the LSI). You will NOT see ANY message from the HP controller when booting! That is because you've configured the PCIe slot ROM option to disabled - and that is exactly what we wanted. (I've put the LSI card into Slot 6 (the one below), with enabled Boot ROM - Reason: I want an external card that runs HW RAID1 (flashed it to IR Firmware)) Remove the Boot ROM card from slot 7 and put in the HP p410 into this slot Boot into the BIOS and under "PCI/PCIe" settings, set the Option ROM to "Disabled" Don't put the HP p410 into any slot of the board Put a card with Boot ROM (in my case my LSI controller) into the topmost slot (7)
#Hp smart array p410i controller how to
Here's a workaround how to get this combination to work*: I've spend some hours last night playing around with the board and both controllers.
![hp smart array p410i controller hp smart array p410i controller](http://www.scsi4me.com/images/HP_P410.jpg)
Don't get me wrong, I can live with mdadm, but HW RAID would be "nicer". Of course - I would love to use the HP RAID controller, but I've the bad feeling that it's incompatible with my board - or am I wrong? Maybe one of you give me a hint. Yesterday, my HP SAS Expander (green) arrived and luckily this one works very well with my "old" LSI/Intel SASUC8i (IT Firmware), so I was able to install Debian on 2x 640GB WD Caviar Blue HDs in RAID1.
#Hp smart array p410i controller update
SuperMicro BIOS update to the latest versionīut I had no luck.
#Hp smart array p410i controller serial
disabled EVERY single (and all together) components on the board (NICs (BOOT ROMs), Serial Port, onboard Storage) "Slot 0 HP Smart Array P410 Initializing \\\"īut I don't get any message how to enter the setup (F8 - I know), once this message is off the screen, the system does a reboot. What I get is the initialization message: I just received the RAID controller 2 days ago and tried to enter the setup. 16GB ECC RAM (4x4GB Kingston DDR3-1333) For my new fileserver, I bought the following hardware: